Whatever you want to know Regarding Hardwood Floor Refinishing

While it ages, hardwood flooring could possibly get scratched and rough. However unlike other styles of flooring, hardwood flooring could make a comeback. All you need to do is refinish it.

Hardwood flooring will take 10 to 12 complete sanding and refinishing tasks throughout its lifetime. Engineered wood flooring can be refinished once of double, based on the wideness of the hardwood veneer.

A word of warning for DIYers: You’ll make savings through doing your own wood floor refinishing, but errors appear big time. The chief challenge is managing a drum sander — a heavy equipment you have from a tool hiring store. Carefully handled, it’s a marvel. But stick around a long time in a single spot and you’ll carve a divot that’ll stare back at you for a long time.

DIY Floor Refinishing

Hardwood floor refinishing is unclean and loud. Usually put on a good dust mask or respirator, ear safeguard, and goggles. Seal doorways off doorways with plastic sheeting and switch off forced-air HVAC to maintain dirt and dust from circulating all through your home.

There are basically two amounts of refinishing hardwood floors.

Buffing is the simplest. If scuff marks and wear are merely on the surface finish as well as the wood underneath is in good condition, you can restore the topcoat by buffing, a procedure also called screening.

You’ll have to rent a floor buffing tool with a number of screen grits to restore the gleam to your floor’s topcoat. A buffing tool is a lot less aggressive than a drum sander and also easier to use. Sweep and then vacuum up any dust between every grit.

Refinish your floors with whatever low-VOC water based finish or maybe polyurethane floor finish (about $60 per gallon).

Notice that hardwood floors that are actually waxed or cleaned with oil soap can’t be buffed until you first remove any remains. Otherwise, you’ll get a blotchy end. Use mineral spirits or perhaps a wax remover to take off any kind of old wax or oil soap before you begin.

Sanding and refinishing hardwood floors will give you the chance to completely restore used, damaged flooring. It additionally gives you the chance to change the shade of your hardwood flooring with spot.

Rent a drum sander and a development of grits — 40 grit, 60 grit, and complete with 100-grit. Remove baseboards. While sanding, maintain the sander moving to prevent gouging the flooring. You won’t manage to get too close to your walls, therefore remove the remaining finish along the sides with a hand-held orbital sander.

After you’ve sanded down to bare wood, fill up any cracks with color-matched wood filler. Use the stain and allow drying completely before applying two to three coats of end.

Call in the Pro

Many expert floor refinishers use equipment with durable dust removal attachments which help keep your house from being messy. Call Wood Floor Planet Now.


For more information visit our site: http://www.woodfloorplanetnj.com/

Floor Sanding vs. screening

Whenever a wood floor loses its shine, the common solution would be to sand it right down to raw wood and totally refinish it. But often, that’s the wrong approach.

All wood floors are guarded by a clear coating that eventually turns into scratched, scuffed and dull. However as long as the damage is shallow—in the covering and not in the wood itself—you can update the floor by adding a brand new coat of polyurethane right over the old end.

This article will assist you to do just that. As with every wood-finishing project, 90 percent of this task is preparation. You have to clean up the floor, touch up any thick scratches and roughen the existing end with sanding screens so the new finish will stick well. Expect to spend one particular full day on this prep work. The re-coating alone usually takes under an hour.

Re-coating takes much less time, ability, and cash than full-scale sanding and refinishing. Even though roughing up the current finish produces lots of dust, it’s still a lot less untidy compared to sanding right down to bare wood. There’s another benefit: Each time you sand a floor down to bare wood, you take away a few of the wood. A strong wood floor can be sanded several times before that’s an issue. However laminated floors (glue-down or floating floors) possess merely a slim layer of nice-looking wood veneer over a plywood-like base. The veneer is generally sanded once or twice—after that, sanding are going to introduce the plywood core beneath.

For more information visit our website: http://www.woodfloorplanetnj.com/

Call us @ 201-330-0909